HD Archives - Joe Tech

How Replace A Motorola Droid RAZR Maxx HD XT912 Screen

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Warning: Division by zero in /var/www/sites/jtnew/wp-content/themes/twentysixteen/functions.php on line 16

Using a spudger (or guitar pick), carefully release all the clips around the edges. The back is affixed to the phone with double-sided adhesive tape. Carefully pull from each corner and edge until it comes away from the phone.

With the battery revealed, remove the three screws along the bottom , the two on the sides, and two on the top corners with a T4 bit. Beware. There is one more screw under the top plastic cover.

Use a guitar pick or similar pry tool to get underneath the camera panel. Be careful around the rear camera.

Remove the final T3 screw.

Use a guitar pick or similar pry tool to release all the clips around the edge of the bezel. Be careful around the buttons and the sim card slot. I released everything I could on the top, bottom, and around the sim card slot. Then I pried loose the sim card slot and the side with the buttons became much easier.

Using tweezers, remove the battery lead cover shown here. Be careful to not connect the two leads with your tweezers or screwdriver. Remove both T5 screws.

SLowly and carefully pry up the battery. Do not use the pull tab as the batter will be taped down pretty securely. Work your way around the edges of the battery until it feels loose enough to pry up and remove it.

Remove the three T3 screws shown here and remove the battery casing.

After removing the battery frame, remove the yellow tape shown here. Now gently release the three black ribbon clamps as shown. In this photo, the first is released and I am about to release the second.

Using a guitar pick or pry tool, release the four clips that hold the camera housing in place. There are two on the top edge of the phone and one on each side. Once those have been released, use a pry tool under the center of the top edge (even with the screw hole) to pry it up slowly. When loose, carefully pull the camera housing away while unplugging the ribbon cables.

Now remove the cable shield as shown here. In this photo, you can see that I am prying it towards me to release a sticking point. There are cables under here, so be careful and use a safe prying tool!

Once the shield is removed, gently pry up the cable connections as shown. Do all three. The section will be able to raise up a little, but do not pull it out.

Starting in the corners, pry around all the edges of the board. Pry only the edges and be very patient. The board is expensive and you can break it if you’re not careful.

Once you’ve removed the broken screen and bezel, you can now put the new one in place. Don’t forget to attach all three ribbon cables. Be patient and line them up if they don’t connect easily.

Remove the two cameras from the housing and first get the rear-facing camera (on the left) in place and attach its ribbon. Then put the housing in place, and finally add the front facing camera and attach its ribbon cable.

Now put the cable cover back in place the same way you got it out.

Replace the battery housing and secure it with the three screws you removed earlier. Then re-attach the battery cable with the screws the match it.

Now replace the plastic outer bezel and make sure all clips snap into place.

Replace all 7 screws in that hold the bezel and camera housing in place.

Now replace the camera lens and flash cover and the antenna on the bottom.

Finally, replace the back cover and give it a little pressure to get it to stick again and you’re done.

If you’ve done everything correctly, you’ll end up with a working phone and a new screen.

Turning Old Hard Drives Into New Clocks

What happens to your old dead hard drive after you’re done with it? Some destroy it to protect sensitive data. Some people just throw theirs away. Then there’s Ben Bedell, an artist with a techie flair who repurposes hard drives as clocks.

I found these hard drive desk clocks for sale at the First Friday Art Walk in Phoenix and they can also be bought online at TimeRecycled.com. Though I haven’t yet bought one, they look even better in person and appear well made.

Computer Art Timepieces

Here’s a little more information from the site:

These are hand-crafted timepieces created from recycled hard drives out of personal computers. Each hard drive is disassembled, painted, and fitted with a timepiece and custom stand. Each unique stand is cut out of recycled motherboards, modems, video cards, and other various electronic components. No two clocks are the same!

Clock hands and hard drive components can be painted in a variety of colors:
– Black, White, Gray, Dark Blue, Blue, Dark Red, Copper
– Red, Orange, Neon Orange, Yellow, Neon Yellow
– Purple, Pink, Dark Green, Green, Neon Green, Teal
– Custom Color Combinations are available

Each clock comes with a “AA” battery so your clock will be ready to keep time.

The clocks run $30 to $40 and cost $10 to ship. That’s not bad for these geeky conversation pieces, but I emailed Ben and he was cool enough to provide a 10% discount to all my readers! Mention JoeTech.com at the time of purchase and he’ll knock 10% off the clock price. Throw one on your desk at the office and let me know what you think.

My Sony Vaio VGN-SZ430N Hard Drive Crashed and How I Fixed It

I use my laptop a lot. I work all day and then I go home and work (and play) some more on my laptop. Sometimes, I go to sleep and my laptop is still running processes (I like to play with theoretical statistics and number crunching). I bought this Sony Vaio last April when my seven year old Dell’s drive finally bit the dust for good and I decided it was time to get a new laptop – one that wasn’t slower than my Windows Mobile cell phone. After seven great years with my Dell, I wouldn’t have guessed that the drive on my new Sony would tank the way it did, and I certainly didn’t anticipate it happening at a critical time like the second day of Affiliate Summit West, but it did.

(note: you can click any image for a large version)

While it would be easier (and cheaper) to just call Sony and have them come out and replace the drive, I opted to do it myself for a few reasons. Mostly, I need to retain the original drive because it contains sensitive client (and personal data), and for those who don’t know, you can usually get a lot of data off an old drive even after it’s been formatted. I didn’t want to take the chance the the drive wouldn’t be disposed of properly. I also think it’s much more fun and provides an excuse to write this post if I do it myself. Besides, someone whose warranty has expired may eventually find and make use of this article.

Before there’s a problem
It seems that the first step in recovering from a hard drive error on my laptop is to kick myself in the butt for not running routine backups. DVDs can be had for about 25 cents each these days, so there is absolutely no reason to not be running backups. I NOW have my laptop set up to run backups once a week to DVD, and if you have a vista laptop, take a look at Sony’s tutorial on how to backup and restore your important files in Windows Vista (it’s a link on that page). I didn’t think I’d need to worry about that yet with a newish laptop and most of my critical files are on my work computer or online, but you really don’t know how much you have to lose until you start to lose it. You should also create (or purchase) your recovery DVDs before you have drive problems. If you wait, you may be without a working laptop for days while you wait for the mail man to bring your disks. Additionally, I think you can still (at the time of this writing) order the recovery disks for Windows XP if you have Vista, just in case you decide you want to downgrade.

Your warranty and my disclaimer
The disclaimer part is simple… If you follow any instructions here, you release me from any claims of liability. It’s your computer and I hope you don’t break anything. With that said, here’s what Sony thinks about you opening up your computer to replace the hard drive yourself:

Hard drive upgrades in the notebook computer are not supported.

NOTES:
* Some notebook computers have instructions for warranty replacement of the hard drive by an end user.
* Although third-party upgrades may be available for some models, they are not supported.
* If the hard drive needs service, repair should be done by an authorized SonyÂ® service center.
* External hard drives may be attached if the appropriate connections are available.

In short, playing doctor with hardware can be fun, but if you can get Sony to replace it for you for free, by all means, do it. If not, keep reading.

The elusive system recovery disks
If you already have recovery disks, skip this section. If you don’t, grab a crossword, TV show, work, or something to read while each DVD burns, two blank DVDs, and make sure you have a spare hour or so for just this process.

After not finding recovery disks, an obvious option on in the computer’s program menus, or any helpful information on Sony’s support pages about how to create recovery disks (did I not search hard enough?), I called support. The first representative told me that there was not a way do create a recovery disk from my existing installation. She then forwarded my call to the parts department so that I could order recovery DVDs. Delivery of the recovery DVDs would take three to five business days, and would cost me $28, I was told. I have no intention of paying for software that I feel should come in the box with the computer and I voiced this concern. The Sony guy explained that they don’t include recovery disks because they’re already on the hard drive. Coming full circle, I had him transfer me back to support so someone could explain how I could burn them. The second support tech put me on hold for a couple minutes and then emailed me the support article and walked me through the following steps, even offering to stay on the phone with me the whole time it was going to take to burn the DVDs. As I imagined someone like me waiting on hold forever for support, I declined so he could help other customers. Here’s the magic recovery disk creation process:

1. Make sure that your laptop is connected to an external power source so the process does not get interrupted.
2. Close all programs.
3. Disconnect any network connections
4. Disconnect any external peripherals (like an external mouse)

5. You can get to the recovery area in one of two ways:
– Search for “vaio recovery center” (this did not work for me) OR
– Hold down the Windows key and hit F1 and then click “Backup and Recovery”

6. Click “Launch Vaio Recovery Center” (at the very bottom)
7. Click “Create Recovery Disks”
8. Click the START button

When prompted, you’ll need to throw in a blank DVD. After it finishes the first DVD, you need to throw in the second blank DVD to make the second recovery disk.

It’s not all that painful once you know how to find the tools to do it.

Replace the bad drive with the new one
Before you start pulling apart your machine, make sure you have both Phillips head and slotted head screwdrivers handy. I also like to keep a blank sheet of paper on a flat surface and a pen handy so I can put screws on it and write where they came from. OK.. lets get started.

1. Unplug the external power supply and remove the battery.

2. Remove 4 screws from the bottom of the laptop.

3. Flip it over and look at the top of the keyboard. To release the keyboard, you’ll need to push in two small tabs. One is just above the F1 and F2 keys, and the other is just above the Insert/Pause key. I gently pressed the tip of the slotted screwdriver into each tab one at a time, while lifting the keyboard with my other hand.

4. Now flip the keyboard toward you, but be careful of that green cable.

5. Remove the three additional chassis screws now visible (circled in the picture below).

6. Flip the keyboard back over and let it rest there.

7. Gently slide the palm rest chassis toward you, but be careful of the hidden white cable.

8. Go ahead and flip it over. THERE’S the hard drive! We’re getting close.

9. Now remove the three hard drive mounting screws shown below. If you have four, you’re lucky. Sony stiffed me a screw.

10. Now you can unplug the SATA cable from the drive. Be very careful to not rip that cable. Mine is taped to the drive, and you may have to give it a little tug. Just be patient and careful with it. AFTER I got mine unplugged, I realized that they taped it on the bottom of the drive, too. You may not even be able to remove the tape until the drive is already out, so have fun with that.

11. Now remove the old drive from it’s cage by removing all four edge screws (they’re hiding under small strips of black tape) and replace it with the new hard drive, replacing the screws, as well.

12. Now you just need to put it all back together by reversing all the directions above and replace the battery and external power connection.

NOTE: We all make mistakes, and I’m not immune. When I got into the BIOS (see below), it wouldn’t find my drive. I pulled it all back apart and realized that I had accidentally disconnected this little guy. Watch out for that.

Format and Install
With every screw back in place, it’s time to set up the drive and bust out your recovery disks. For starters, turn on the power and hit the F2 key while booting to enter the BIOS to make sure the drive is recognized. Put in the first recovery disk and then turn the computer off and then back on again. On the screen that pops up, select “Vaio Recovery Center”.

On the next screen, select “Skip” and click the “Next” button. You will be given an option to install all the extras Sony wants to install. Although I’ll end up removing many of them, I installed all of them for the few I will use. Make your own choice here and then proceed with the installation.

After a disk swap, lots of waiting, a bunch of steps and a few reboots, Windows Vista’s installation and configuration will begin and a short time later, you’re back in business.

Am I all done?
Nope. Remember what I said about backups when we started? Well, you have a clean install and a good drive. Now’s the time to set up your routine backups before you start loading your drive up with critical data. While you’re at it, set up that firewall and anti-virus software.